Man-1078_Sigma_CP_22 Page 10 of 24 5B6. Connecting to the circuit board All connections for field wiring are to a single row of terminals along
Man-1078_Sigma_CP_22 Page 11 of 24 + -ZONE + IN+ OUT-IN-OUTDETECTORCALL POINT 6K8 END OF LINE RESISTOR+ -ZONE + IN+ OUT-IN-OUT
Man-1078_Sigma_CP_22 Page 12 of 24 8B9. Sounder circuit wiring Whether using standard or T series control panels, all sounders must
Man-1078_Sigma_CP_22 Page 13 of 24 10B11. Aux 24V DC supply An auxiliary 24V DC supply is provided to enable local signalling or control of anc
Man-1078_Sigma_CP_22 Page 14 of 24 For panels with software version Sigma242.hex or below, the Enable controls keyswitch and Write Enable switc
Man-1078_Sigma_CP_22 Page 15 of 24 15B16. Panel operation 24B16.1 Normal condition Under normal conditions, control panels will have only the
Man-1078_Sigma_CP_22 Page 16 of 24 Note: The flashing “dx” indicator will only appear on panels with software version sigma_CP 214.hex and high
Man-1078_Sigma_CP_22 Page 17 of 24 Table 8 – Configuration codes CODE FUNCTION COMMENTS 00 SOUNDER DELAY TIME = 30 SECONDS Sets th
Man-1078_Sigma_CP_22 Page 18 of 24 61 CONFIGURE Z1 FOR I.S BARRIER Detection threshold changed for use with IS barrier 62 CONFIGURE Z2 FOR I.S
Man-1078_Sigma_CP_22 Page 19 of 24 Once the required configuration options have been set, the Write enable switch must be returned
Man-1078_Sigma_CP_22 Page 2 of 24 Index Page 0B1. Introduction ...
Man-1078_Sigma_CP_22 Page 20 of 24 45B20.7 Sys fuse fault Indicates that the total power rating of the power supply has been exceeded and that
Man-1078_Sigma_CP_22 Page 21 of 24 21. Power supply The control panel requires a 230V (+10%/-15%), 50/60Hz, AC mains power supply which connect
Man-1078_Sigma_CP_22 Page 22 of 24 22. Maintenance Sigma CP control panels do not require any specific maintenance but should the control panel
Man-1078_Sigma_CP_22 Page 23 of 24 23B24. Record of Configuration Use the table below to record the configuration codes that have been s
Man-1078_Sigma_CP_22 Page 24 of 24 CODE FUNCTION COMMENTS SET 71* ZONE 1 SHORT CIRCUIT INDICATES ALARM Changes the trigger threshold o
Man-1078_Sigma_CP_22 Page 3 of 24 0B1. Introduction The SIGMA CP range consists of a series of conventional fire alarm control panels designed
Man-1078_Sigma_CP_22 Page 4 of 24 Mounting The control panel should be mounted on a dry, flat surface, at eye height to the dis
Man-1078_Sigma_CP_22 Page 5 of 24 Table 3 - Battery charge voltage versus temperature Temperature 0C Battery charge voltage 0 29.2 10 28.56 20
Man-1078_Sigma_CP_22 Page 6 of 24 Although the current consumption of many detection devices would allow more than 32 to be connected to a zone
Man-1078_Sigma_CP_22 Page 7 of 24 Table 5 - Compatible detector bases and call points Model Type Manufacturer Comments YBN-R/4 STANDARD Hochiki
Man-1078_Sigma_CP_22 Page 8 of 24 3B4. Using intrinsically safe barriers SIGMA CP control panels support the use of I.S. barriers for connectin
Man-1078_Sigma_CP_22 Page 9 of 24 4B5. Control panel fascia In addition to the mandatory controls and indications required by the EN54-2 s
Commentaires sur ces manuels